Resultado de búsqueda
Synchronization within 16.7 s max, reference to the coordinated system time. Power dissipation, max. 4.5 W @ 60 °C (140 °F) Isolation voltage. 250V (continuous), basic insulation type, outputs-to-backplane, and output-to-output. Wire category.
- Relay
- DC
- DC
- Summary of Changes
- North American Hazardous Location Approval
- Prevent Electrostatic Discharge
- Removal and Insertion Under Power
- Key the Module and Removable Terminal Block or Interface Module
- Wire the Module
- Assemble the Removable Terminal Block and the Housing
- Install the Removable Terminal Block onto the Module
- Remove the Removable Terminal Block from the Module
- Remove the Module
- Additional Resources
- Rockwell Automation Support
- Documentation Feedback
These updated installation instructions include new and revised content as shown in this table. ATTENTION: Read this document and the documents listed in the Additional Resources section about installation, configuration and operation of this equipment before you install, configure, operate or maintain this product. Users are required to familiariz...
The following information applies when operating this equipment in hazardous locations: Products marked ‘CL I, DIV 2, GP A, B, C, D’ are suitable for use in Class I Division 2 Groups A, B, C, D, Hazardous Locations and nonhazardous locations only. Each product is supplied with markings on the rating nameplate indicating the hazardous location tempe...
ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: Touch a grounded object to discharge potential static. Wear an approved grounding wriststrap. Do not touch connectors or pins on component boards. Do not touch circui...
WARNING: When you insert or remove the module while backplane power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. Repeated electrical arcing causes excessive wear to contacts on both the module and its mating connect...
Use the wedge-shaped keying tabs and U-shaped keying bands to prevent connecting the wrong wires to your module.
You can connect wiring to your module with only an RTB.
Align the grooves at the bottom of the housing with the side edges of the RTB. Groove Side edge of the RTB Groove Strain relief area Side edge of the RTB Slide the RTB into the housing until it snaps into place.
WARNING: If you connect or disconnect the removable terminal block (RTB) with field-side power applied, an electrical arc can occur. This could cause an explosion in hazardous location installations. Before proceeding with RTB installation, make certain: power is removed or the area is nonhazardous. field-side wiring of the RTB has been completed. ...
If you need to remove the module, you must first remove the RTB. WARNING: When you insert or remove the module while backplane power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. Before removing the module, you must ...
Push in top and bottom locking tabs. Pull module out of the chassis.
These documents contain additional information concerning related products from Rockwell Automation. You can view or download publications at https://www.rockwellautomation.com/en_NA/overview.page. Notes:
Use these resources to access support information.
Your comments help us serve your documentation needs better. If you have any suggestions on how to improve our content, complete the form at rok.auto/docfeedback.
Literature Library | Rockwell Automation
- 6MB
- 258
CE. Australian RCM. This product was certified with the above certifications as of 2024-06-05. Products sold before or after this date might carry different certifications. Please review the product label to check for the certifications your specific product carries. ControlLogix 16 Point Digital Output Rel.
1756 ControlLogix I/O Modules Technical Documentation. Looking for specifications? Need manuals to help you install, configure, and use your 1756 ControlLogix® I/O and chassis-based communication modules? You can find it here.
Safety 1756-IB16S 226 1756-OBV8S 234 Contact 1756-OW16I 1756-OX8I 244 247 Analog 1756-IF6CIS 1756-IF6I 1756-IF8, 1756-IF8K 1756-IF8I, 1756-IF8IK 1756-IF16, 1756-IF16K
1756 ControlLogix/GuardLogix System. N.O. Isolated Relay Output 16 Pts (36 Pin) Digital Contact Output Modules (Please select number of Removable terminal Blocks as addded in the list.)
