Resultado de búsqueda
29 de jul. de 2022 · Huge Delay on Focusrite Scarlett Solo 3rd Gen. I've updated my driver and Focusrite Control to the latest one from the site (Focusrite Control 3.11.0) and after a restart after installing it, it was fine, but after a few hours of voice chatting with my friends, I noticed that my friends reply to me a bit late and I know it wasn't my WiFi, so I ...
5 de ago. de 2021 · I might just send the Solo back, seems like unneeded complexity. I have the audio gain up on the mic, and it's all working fine. Using Shure MV7 with USB straight to PC works 100% fine, but low gain, so I got the Solo. Now going XLR -> Solo -> PC only getting the left-hand side of the audio. Using Adobe Audition, I can see only the left channel ...
18 de abr. de 2021 · Generally, the rule is low buffer size when recording voice/instruments, playing on a MIDI keyboard, etc. and high buffer size when mixing/mastering. You could go as low as 32 when recording, if your CPU handles it and as high as 1024 when mixing or when you’re simply listening to music, if your CPU needs it. You are using the full potential ...
29 de ene. de 2020 · Just leave it set to Real Tone Cable! -Verify your scarlett solo is set to 48000 sample rate and 48 buffer size. -Edit the RS_ASIO.ini file you downloaded, put semicolons in front of the ; [Asio.Input.0] section, and remove the semicolons in front of the [Asio.Input.1] section (my file is inserted below for reference. Verify BufferSizeMode=custom.
14 de oct. de 2020 · Focusrite Scarlett Solo as a DAC/AMP combo recommendation. Discussion. I've been using a Focusrite Scarlett Solo as a USB-C DAC and headphone amp, I've found it to be powerful enough to drive my HD600 to good volume levels, and is plug-and-play with Mac/Windows/iPad Pro. I never see anyone recommend the Solo as an affordable DAC/AMP combo, and ...
10 de nov. de 2020 · The sample rate, buffer size and audio directing could be an issue too. In your DAW, the sample rate and buffer size should match the focusrite's. Make sure to also use Focusirte ASIO. I have a brand new Scarlett Solo and it's giving me lots of distortion or clipping or high gain...not sure which. This is just playing into direct….
19 de oct. de 2021 · The 48v is for phantom power, to provide power to condenser microphones. If you're not using equipment that requires phantom power, be careful to not have it turned on or you run the risk of damaging the equipment that was not intended to have phantom power. With respect to the Air mode; it is essentially a mic pre-amp that can be used to boost ...
24 de oct. de 2022 · What fixed it was to install Nvidia "Studio Drivers" instead of "Game Ready Drivers". also before finding the fix, two things seemed to make things better : enabling "Low Latency Mode" to "On" and "Power Management Mode" to "Prefer Maximum Performance" in Nvidia Control Panel settings > Manage 3D Settings. Hope that it can help you.
25 de jul. de 2021 · The SM7B has a TIGHT cardioid pattern, it's designed for your mouth to be right up to the mic. Like, put your pop shield (if you're using one) almost right against the mic itself and have your mouth no more than 3" away. It is designed for CLOSE-MIKING voices. That's why it sounds quiet. You're just not close enough.
27 de ago. de 2022 · I have tried: - Switching USB ports. - Updating the firmware. - Restarting my computer. - Turning off/on phantom power. - Unplugging my dock from my laptop. - Unplugging my microphone and guitar cables. - Disabled power saving mode on the USB port the interface is plugged into. I don't know what else I can do.
