Resultado de búsqueda
This manual describes how to install, configure, and troubleshoot your ControlLogix® High-speed Counter (HSC) module, catalog number 1756-HSC, herein referred to as the module. Based on your module series and firmware revision, there are programming software requirements to use some module features.
- 3MB
- 124
- Prevent Electrostatic Discharge
- Install the Module
- Connect Ungrounded End of the Cable
- Wire a Cage-clamp RTB
- Wire Terminations
- Install the Removable Terminal Block
- Remove the Removable Terminal Block
- Remove the Module from the Chassis
- Additional Resources
- Description
ATTENTION: This equipment is sensitive to electrostatic discharge, which can cause internal damage and affect normal operation. Follow these guidelines when you handle this equipment: Touch a grounded object to discharge potential static. Wear an approved grounding wriststrap. Do not touch connectors or pins on component boards. Do not touch circui...
You can install or remove the module while chassis power is applied. WARNING: When you insert or remove the module while backplane power is on, an electric arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. Repeated electrical arcing causes e...
Follow these directions to connect the ungrounded end of the cable. Cut the foil shield and drain wire back to the cable casing and apply shrink wrap. Connect the insulated wires to the RTB.
Insert the wire into the terminal. Turn the screw clockwise to close the terminal on the wire.
The following sections provide details about wiring terminations to specific products.
These steps show how to install the RTB onto the module to connect the wiring. WARNING: When you connect or disconnect the Removable Terminal Block (RTB) with field side power applied, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proc...
If you must remove the module from the chassis, you must first remove the RTB from the module. Do these steps to remove the RTB. WARNING: When you connect or disconnect the Removable Terminal Block (RTB) with field side power applied, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power ...
Follow these steps to remove a module from its chassis. WARNING: When you insert or remove the module while backplane power is on, an electrical arc can occur. This could cause an explosion in hazardous location installations. Be sure that power is removed or the area is nonhazardous before proceeding. Repeated electrical arcing causes excessive we...
These documents contain additional information concerning related products from Rockwell Automation.
Provides specification information for the ControlLogix I/O modules. Provides detailed information about installation and use of the high-speed counter module. Provides general guidelines for installing a Rockwell Automation industrial system. Provides declarations of conformity, certificates, and other certification details. You can view or downlo...
- 1018KB
- 12
ControlLogix High Speed Counter Module.
Cables are available in 0.5m, 1.0m, 2.5m, and 5.0m standard lengths (005=0.5m, 010=1.0m, 025=2.5m, 050=5.0m). Custom length cables are also available. Terminals starting with A are the lower row of terminals, B terminals are the upper row.
In-depth information on grounding and wiring Allen-Bradley programmable controllers Allen-Bradley Programmable Controller Grounding and Wiring Guidelines 1770-4.1 A description of important differences between solid-state programmable controller products and hard-wired electromechanical devices Application Considerations for Solid-State ...
- 1MB
- 140
Capítulo Configure el módulo 1756-HSC Introducción Este capítulo describe cómo configurar el módulo 1756-HSC/B, revisión de firmware 3.x, usando el software de programación RSLogix 5000, versión 18 y posterior. Su módulo 1756-HSC no funcionará hasta que haya sido configurado.
View and Download Rockwell Automation Allen-Bradley ControlLogix 1756-HSC user manual online. High-speed Counter Module. Allen-Bradley ControlLogix 1756-HSC control unit pdf manual download.
